Essential Plumber Tips for Bathtub Installation
Essential Plumber Tips for Bathtub Installation
Blog Article
Do you find yourself hunting for help and advice concerning How to Install a Bathtub?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is also a reasonably difficult task. If the old bathtub is conveniently available, the task can move immediately; if you need to open a wall to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified on your own for the work and also are comfortable trying it. Instead of hiring a professional to take over a halfway-completed project, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you might need a professional plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your washroom if you have actually already gotten a brand-new tub and also do not need to alter the setup of your previous supply of water pipelines.
Your devices and also material checklist must consist of the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you should do is detach the supply of water. After doing so, activate the taps to drain any water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the limited accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of both wooden boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in equally spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bath tub till the level reviews degree.
To install taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the tub as well as also examine the overflow outlet as well as the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been used at the very least when as this will certainly settle it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in place between the faucet and also the sink. Safeguard the tap in position with the manufacturer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind should be linked to the tap ends initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break an inflexible seal, creating the water to pass through the wall surface between the bath and also the tiling, leading to difficulties with wetness and possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the tub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly offered on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted person who reads on How to Install a Bathtub, I was thinking sharing that editorial was valuable. Enjoyed our article? Please share it. Help another person check it out. I treasure reading our article about How to Install a Bathtub.
Detail Report this page